Front Power Seat Motor Removal and Installation
Slide Motor

2. Slide Motor - Remove

1.
Remove the slide motor cover (A).






2.
Release the cable housing (A) from the hooks (B).

3.
Disconnect the flex cable (C) from the warm gear (D).

4.
Disconnect the flex cable from the slide motor (E).

NOTE: Take care not to kink the cable.






5.
Disconnect the connector (A).

6.
Detach the harness clip (B).

7.
Remove the bolts (C) with a TORX T30 bit.





8.
Disconnect the slide motor (A) from the short flex cable (B), then remove the slide motor bracket (C).





9.
Remove the short flex cable (A).





10.
Remove the slide motor (A).

Front Up-Down Motor (For Some Models)

2. Front Up-Down Motor - Remove


1.
Disconnect the connector (A).

2.
Remove the bolts (B, C) with TORX T30 and T40 bits, then remove the front up-down motor assembly (D).






3.
Detach the connector clip (A), and remove the bolts (B) with a TORX T30 bit.

4.
Remove the front up-down motor (C) from the front up-down motor bracket (D).

Rear Up-Down Motor (For Some Models)

3. Rear Up-Down Motor - Remove

1.
Remove the bolts (A, B) with TORX T30 and T40 bits, then remove the rear brake bracket (C).





2.
Remove the gear (A).






3.
Disconnect the connector (A), then detach the connector clip (B).

4.
Remove the bolts (C) with a TORX T30 bit, then remove the rear up-down motor (D).

Slide Motor

1. Slide Motor - Install

1.
Install the slide motor (A).





2.
Install the short flex cable (A) to the worm gear (B).

NOTE: Apply multipurpose grease to the worm gear area indicated by the arrows.





3.
Install the slide motor (A) to the short flex cable (B), then install the slide motor bracket (C).






4.
Install the bolts (A) with a TORX T30 bit.

5.
Install the harness clip (B).

6.
Connect the connector (C).






7.
Install the flex cable (A) to the slide motor (B).

NOTE: Take care not to kink the cable.

8.
Install the flex cable to the warm gear (C).

NOTE: Apply multipurpose grease to the worm gear area indicated by the arrows.

9.
Install the cable housing (D) to the hooks (E).





10.
Install the slide motor cover (A).

Front Up-Down Motor (For Some Models)

1. Front Up-Down Motor - Install


1.
Install the front up-down motor (A) to the front up-down motor bracket (B).

2.
Install the bolts (C) with a TORX T30 bit, then install the connector clip (D).







3.
Install the front up-down motor assembly (A).

NOTE:
Apply multipurpose grease to the pivot portions of the up-down adjuster and the motor pinion (B) indicated by the arrows.
When installing the front up-down motor assembly, adjust the gear (C) to the motor pinion by slightly rotating the brake (D) with an 8 mm hex wrench.

4.
Install the bolts (E, F) with TORX T30 and T40 bits.

5.
Connect the connector (G).

Rear Up-Down Motor (For Some Models)

1. Rear Up-Down Motor - Install


1.
Remove the bolts (A) with a TORX T30 bit.

2.
Remove the rear brake (B) from the rear brake bracket (C).






3.
Install the rear up-down motor (A), then install the bolts (B) with a TORX T30 bit.

NOTE: Apply multipurpose grease to the motor pinion (C) indicated by the arrows.

4.
Install the connector clip (D), then connect the connector (E).






5.
Manually raise the seat frame (A) fully upward.

6.
Install the gear (B) with its chamfered side faced the seat frame.

NOTE: Apply multipurpose grease to the gear indicated by the arrows.





7.
Install the rear brake bracket (A).

NOTE: Lightly fasten all of the bolts (B, C) with TORX T30 and T40 bits.






8.
Carefully position the seat frame on its rear up-down motor side down.

9.
Engage the gear (A) with the motor pinion by hand, and center it.

10.
Check the positions of the sector gear (B) and the cross-shaped hole (C) in the gear.

11.
Align the pinion (D) on the rear brake with the sector gear with an 8mm hex wrench, and align the fingers (E) around the axle with the cross-shaped hole in the gear.





12.
Install the rear brake (A) on to the rear brake bracket (B) while holding the gear (C) perpendicular to the axle of the rear brake by hand.

NOTE:
If you feel any interference between inside gears. Remove the rear brake, and repeat steps 9 to 11.
If the rear brake seats fully on the rear brake bracket with no interference, go to step 13.






13.
Install the bolts (A) with a TORX T30 bit.

14.
Tighten the bolts (B, C) to specified torque with TORX T30 and T40 bits.