Lower Valve Body Removal and Installation

NOTE:
Keep all foreign particles out of the transmission.
The lower valve body and the following parts are not available separately. Replace them as a set.
?CVT clutch pressure control solenoid valve
?CVT drive pulley pressure control solenoid valve
?CVT driven pulley pressure control solenoid valve
?CVT lock-up clutch control solenoid valve
?Shift solenoid valve B

2. Transmission Fluid Strainer - Remove
1.
Remove the transmission fluid strainer (A) with the O-ring (B).
2.
Clean the inlet opening (A) of the transmission fluid strainer thoroughly with compressed air.
3.
Check that it is in good condition and that the inlet opening is not clogged.
4.
Test the strainer by pouring clean transmission fluid through the inlet opening, and replace it if it is clogged or damaged.

3. Lower Valve Body Assembly - Remove
1.
Remove the transmission fluid temperature sensor (A).
2.
Disconnect the connectors (B).
3.
Remove the guide plate (A).
4.
Remove the lower valve body assembly (B), and hold the lower valve body assembly.
NOTE:
Check that the lower valve body assembly is free of solenoid wire harness A.
Do not damage solenoid wire harness A and B while removing the lower valve body assembly.
5.
Remove the 10.9 x 26 mm pipe (A) with the O-rings (B).
6.
Remove the 8 x 133.5 mm pipe.
7.
Remove the 12 x 56.7 mm pipe (A) with the O-rings (B).
8.
Remove the 8 x 71.5 mm pipe (C).
9.
Remove the 14.3 x 36.2 mm pipe (D) with the O-rings (E).
10.
Remove the 10.9 x 18.5 mm pipes (A) with the O-rings (B).
11.
Remove the 18 x 18 mm pipes (A) with the O-rings (B).


NOTE:
Keep all foreign particles out of the transmission.
The lower valve body and the following parts are not available separately. Replace them as a set.
?CVT clutch pressure control solenoid valve
?CVT drive pulley pressure control solenoid valve
?CVT driven pulley pressure control solenoid valve
?CVT lock-up clutch control solenoid valve
?Shift solenoid valve B

1. Lower Valve Body Assembly - Install
1.
Install the 18 x 18 mm pipes (A) with new O-rings (B).
2.
Install the 10.9 x 18.5 mm pipes (A) with new O-rings (B).
3.
Install the 14.3 x 36.2 mm pipe (A) with new O-rings (B).
4.
Install the 8 x 71.5 mm pipe (C) with the filter end (D) facing the lower valve body assembly into the transmission.
5.
Install the 12 x 56.7 mm pipe (E) with new O-rings (F).
6.
Install the 8 x 133.5 mm pipe.
7.
Install the 10.9 x 26 mm pipe (A) with new O-rings (B).
8.
Install the lower valve body assembly (A), and tighten them in a crisscross pattern in at least two steps.
NOTE:
Do not pinch the solenoid wire harnesses.
Do not damage the solenoid wire harnesses while installing the lower valve body assembly.
Length of Bolt
B
90 mm (3.54 in)
C
80 mm (3.15 in)
D
65 mm (2.56 in)
E
55 mm (2.17 in)
F
40 mm (1.57 in)
9.
Install the guide plate (G).
10.
Connect these connectors (A).
11.
Install the transmission fluid temperature sensor (B).

2. Transmission Fluid Strainer - Install
1.
Install the transmission fluid strainer (A) with a new O-ring (B).
NOTE:
Install the transmission fluid strainer carefully to prevent damaging the O-ring.
Do not pinch the solenoid wire harnesses.