DTC Troubleshooting: B1028
DTC B1028: Rear Wiper Motor (Park) Signal Error
DTC Description
DTC
B1028 Rear wiper motor(Park) signal error
 

NOTE: If you are troubleshooting multiple DTCs, be sure to follow the instructions in B-CAN System Diagnosis Test Mode A.

1.
Problem verification:

Problem verification
?1.
Clear the DTCs with the HDS.


?2.
Turn the vehicle to the OFF (LOCK) mode and then the ON mode.

?3.
Turn the rear window wiper switch to ON for 15 seconds or more, then turn the switch OFF.

?4.
Check for DTCs with the HDS.
DTC Description
DTC
B1028 Rear wiper motor(Park) signal error
 

Is DTC B1028 indicated?

     
YES
     
     
     
Without keyless access system: go to step 2.
     
YES
     
     
     
With keyless access system: go to step 4.
     
NO
     
     
     
Intermittent failure, the system is OK at this time. Check for loose or poor connections.?
2.
Fuse check:

Fuse check
?1.
Check the following fuse.
Fuse
No. B23 (10 A)
Location
Under-dash fuse/relay box

Is the fuse OK?

     
YES
     
     
     
Go to step 3.
     
NO
     
     
     
Replace the fuse. If the fuse blows again, repair the short to ground in the No. B23 (10 A) fuse circuit.?
3.
Open wire check (IG1 WIPER&WASHER line):

Open wire check (IG1 WIPER&WASHER line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Rear window wiper motor 4P connector

?3.
Turn the vehicle to the ON mode.

?4.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
Rear window wiper motor 4P connector: disconnected
Test point 1
Rear window wiper motor 4P connector No. 2
Test point 2
Body ground


Is there battery voltage?

     
YES
     
     
     
IG1 WIPER&WASHER wire is OK. Go to step 6.
     
NO
     
     
     
Repair an open or high resistance in the wire.?
4.
Fuse check:

Fuse check
?1.
Check the following fuses.
Fuse
No. B23 (10 A)
No. B36 (10 A)
Location
Under-dash fuse/relay box

Is each fuse OK?

     
YES
     
     
     
Go to step 5.
     
NO
     
     
     
Replace the fuse. If the fuse blows again, repair the short to ground in the No. B23 (10 A) and/or No. B36 (10 A) fuse circuit(s).?
5.
Open wire check (RR WIPER MAIN RLY OUT line):

Open wire check (RR WIPER MAIN RLY OUT line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Disconnect the following connector.
Rear window wiper motor 4P connector

?3.
Turn the vehicle to the ON mode.

?4.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle ON mode
Rear window wiper motor 4P connector: disconnected
Test point 1
Rear window wiper motor 4P connector No. 2
Test point 2
Body ground


Is there battery voltage?

     
YES
     
     
     
The RR WIPER MAIN RLY OUT wire is OK. Go to step 6.
     
NO
     
     
     
Repair an open or high resistance in the wire.?
6.
Open wire check (GND line):

Open wire check (GND line)
?1.
Turn the vehicle to the OFF (LOCK) mode.

?2.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Rear window wiper motor 4P connector: disconnected
Test point 1
Rear window wiper motor 4P connector No. 3
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
The GND wire is OK. Go to step 7.
     
NO
     
     
     
Repair an open or high resistance in the ground wire or poor ground (G603).?
7.
Rear window wiper motor check:

Rear window wiper motor check
?1.

Does the wiper motor run and does it pulse normally?

     
YES
     
     
     
Go to step 8.
     
NO
     
     
     
8.
Shorted wire check (RR WIPER RLY CL- line to power):

Shorted wire check (RR WIPER RLY CL- line to power)
?1.
Disconnect the following connector.
Under-dash fuse/relay box connector T (20P)

?2.
Measure the voltage between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Rear window wiper motor 4P connector: disconnected
Under-dash fuse/relay box connector T (20P): disconnected
Test point 1
Rear window wiper motor 4P connector No. 4
Test point 2
Body ground


Is there battery voltage?

     
YES
     
     
     
Repair a short to power in the wire to power.?
     
NO
     
     
     
The RR WIPER RLY CL- wire is not shorted to power. Go to step 9.
9.
Shorted wire check (RR WIPER RLY CL- line):

Shorted wire check (RR WIPER RLY CL- line)
?1.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Rear window wiper motor 4P connector: disconnected
Under-dash fuse/relay box connector T (20P): disconnected
Test point 1
Rear window wiper motor 4P connector No. 4
Test point 2
Body ground


Is there continuity?

     
YES
     
     
     
Repair a short to ground in the wire.?
     
NO
     
     
     
The RR WIPER RLY CL- wire is not shorted. Go to step 10.
10.
Open wire check (RR WIPER RLY CL- line):

Open wire check (RR WIPER RLY CL- line)
?1.
Check for continuity between test points 1 and 2.
Test condition
Vehicle OFF (LOCK) mode
Rear window wiper motor 4P connector: disconnected
Under-dash fuse/relay box connector T (20P): disconnected
Test point 1
Rear window wiper motor 4P connector No. 4
Test point 2


Is there continuity?

     
YES
     
     
     
The RR WIPER RLY CL- wire is OK. Faulty MICU; replace the under-dash fuse/relay box.?
     
NO
     
     
     
Repair an open or high resistance in the wire.?