Front Stabilizer Bar Removal and Installation
Special Tools Required
Image Description/Tool Number
8616757.png Ball Joint Remover, 28 mm 07MAC-SL00202
609765.png Ball Joint Thread Protector, 12 mm 07AAF-SDAA100
310292.png Subframe Adapter VSB02C000016*
*Available through the Honda Tool and Equipment Program 888-424-6857

NOTE: Lower the front subframe from the body, and replace the front stabilizer bar through the gap created by lowering the front subframe.

3. Steering Wheel - Hold


1.
Center the steering wheel spoke angle.

2.
Install a commercially available steering wheel holder tool (A).

4. Steering Joint Cover - Remove


5. Steering Column Lower Slide Shaft - Hold

1.
Set the steering column to the center tilt position, and to the center telescopic position.

2.
Hold the lower slide shaft (A) on the column with a piece of wire (B) between the joint yoke (C) of the lower slide shaft and the joint yoke (D) of the upper shaft to prevent the lower slide shaft from pulling out.

6. Steering Joint - Disconnect


1.
Remove the steering joint bolt (A).

2.
Disconnect the steering joint (B) from the pinion shaft.

NOTE:
If the center guide (C) is in place and has not moved, leave it in place.
If the center guide has come off, discard it.

7. Tie-Rod End Ball Joint - Disconnect


1.
Remove the cotter pin (A).

2.
Remove the nut (B).

3.

NOTE: Be careful not to damage the ball joint boot when installing the ball joint remover.

13. Front Subframe - Support


1.
Attach the subframe adapter to the front subframe by looping the strap (A) over the front of the front subframe (B), then secure the strap with stop (C), then tighten the wing nut (D).

2.
Raise the transmission jack and line up the slots in the arms with the bolt holes on the corner of the jack base, then tighten the bolts.

14. Lower Torque Rod - Remove

1.
Remove the lower torque rod mounting bolts (A).

15. Front Subframe - Lift Down

1.
Remove the mid mounting bolt (A) on both sides.





2.
Loosen the front subframe mounting bolt (A) so they are about 30 mm (1.18 in) from the mounting surface on both sides.

NOTE: Do not loosen the front subframe mounting bolts more than necessary.






3.
Remove the front subframe mounting bolts (A) on both sides.

4.
Lower the jack slowly until the front subframe has dropped about 130 mm (5.12 in).

16. Stabilizer Bar - Remove


1.
Remove the bushing holder (A) on both sides.

2.
Remove the bushing (B) on both sides.

3.
Remove the front stabilizer bar (C).

NOTE: Be careful not to damage the steering gearbox.

1. Stabilizer Bar - Install


1.
Install the stabilizer bar (A).

NOTE: Be careful not to damage the steering gearbox.

2.
Install the bushing (B) on both sides.

NOTE:
Note the direction of installation for the bushing.
Align the paint mark (C) on the stabilizer bar with the side of the bushing.

3.
Install the bushing holder (D) on both sides.

2. Front Subframe - Move


1.
Turn the lip (A) of the pinion shaft grommet.

2.
Raise the front subframe (B) up to the body, then restore the pinion shaft grommet back to proper position.

NOTE: Be sure that the pinion shaft grommet is secure in place. Make sure the lip of the pinion shaft grommet is not turned up. Incorrect installation can cause leakage of water and mud, or noise.

3. Front Subframe Mounting Bolt - Loosely Install


1.
Loosely install a new front subframe mounting bolts (A) on both sides.





2.
Loosely install a new mid mounting bolt (A) on both sides.

5. Lower Torque Rod - Connect

1.
Loosely install new lower torque rod mounting bolts (A).





2.
Loosen the lower torque rod mounting bolt (A) to the subframe side.






3.
Tighten the lower torque rod mounting bolts (A) to the oil pan side.

4.
Tighten the lower torque rod mounting bolt (B) to the subframe side.

11. Tie-Rod End Ball Joint - Connect


1.
Wipe off any grease contamination from the ball joint tapered section and threads.

2.
Connect the tie-rod ball joint (A) to the knuckle.

3.
Install the nut (B).

4.
Install a new cotter pin (C).

NOTE: Bend the cotter pin as shown.

12. Steering Column Lower Slide Shaft - Release

1.
Cut the wire (A).

13. Steering Wheel - Release


14. Steering Joint - Connect


1.
Set the rack in the straight ahead driving position.

2.
Slip the lower end of the steering joint (A) onto the pinion shaft (B).

NOTE:
Pinion shaft with center guide: Install the steering joint by aligning the center guide (C).
Pinion shaft without center guide: Position the steering column by aligning the gap (D) within the angle.






3.
Align the bolt hole (A) on the steering joint with the groove (B) around the pinion shaft.

4.
Loosely install the steering joint bolt (C).

5.
Be sure that the joint bolt is securely in the groove in the pinion shaft.

6.
Pull on the steering joint to make sure that the steering joint is fully seated.

7.
Tighten the steering joint bolt to the specified torque.

15. Steering Joint Cover - Install