|
DTC Advanced Diagnostics: SRS related DTCs
SRS Related DTCs
NOTE
|
|
The "x" at the end of each DTC denotes a numeric character (0 thru 9) or an alpha character (A thru F) that you may also see on the HDS display. The alphanumeric character is unrelated to the AD information or DTC troubleshooting; it is used by the SRS unit manufacture. |
|
|
Always check "How to troubleshoot the SRS system" and proceed along each "DTC Troubleshooting" procedure. |
|
|
Make sure the 12 volt battery is fully charged. If not, the results of tests may not be accurate. |
|
|
The SRS indicator will turn on when the 12 volt battery voltage becomes below 10 volts. |
|
|
The possible causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes. |
DTC 11-1x: Open in the Left Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the left front airbag 1st inflator (LA1+, LA1- lines) |
|
|
Left front airbag internal failure (Left front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-2x: Increased Resistance in the Left Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left front airbag 1st inflator (LA1+, LA1- lines) |
|
|
Left front airbag internal failure (Left front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-3x: Short to Another Wire or Decreased Resistance in the Left Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the left front airbag 1st inflator (LA1+, LA1- lines) |
|
|
Left front airbag internal failure (Left front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-4x: Open in the Left Front Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the left front airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Left front airbag internal failure (Left front airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-5x: Increased Resistance in the Left Front Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left front airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Left front airbag internal failure (Left front airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-6x: Short to Another Wire or Decreased Resistance in the Left Front Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the left front airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Left front airbag internal failure (Left front airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-8x: Short to Power in the Left Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the left front airbag 1st inflator (LA1+, LA1- lines) |
|
|
Left front airbag internal failure (Left front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-9x: Short to Ground in the Left Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the left front airbag 1st inflator (LA1+, LA1- lines) |
|
|
Left front airbag internal failure (Left front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-Ax: Short to Power in the Left Front Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the left front airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Left front airbag internal failure (Left front airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC 11-Bx: Short to Ground in the Left Front Airbag 2nd Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the left front airbag 2nd inflator (LA2+, LA2- lines) |
|
|
Left front airbag internal failure (Left front airbag 2nd inflator) |
|
|
SRS unit internal failure | | |
|
DTC 12-1x: Open in the Right Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the right front airbag 1st inflator (RA1+, RA1- lines) |
|
|
Right front airbag internal failure (Right front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 12-2x: Increased Resistance in the Right Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right front airbag 1st inflator (RA1+, RA1- lines) |
|
|
Right front airbag internal failure (Right front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 12-3x: Short to Another Wire or Decreased Resistance in the Right Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the right front airbag 1st inflator (RA1+, RA1- lines) |
|
|
Right front airbag internal failure (Right front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 12-8x: Short to Power in the Right Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the right front airbag 1st inflator (RA1+, RA1- lines) |
|
|
Right front airbag internal failure (Right front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 12-9x: Short to Ground in the Right Front Airbag 1st Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the right front airbag 1st inflator (RA1+, RA1- lines) |
|
|
Right front airbag internal failure (Right front airbag 1st inflator) |
|
|
SRS unit internal failure | | |
|
DTC 21-1x: Open in the Left Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the left front seat belt tensioner (LRP+, LRP- lines) |
|
|
Left front seat belt internal failure (Left front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 21-2x: Increased Resistance in the Left Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left front seat belt tensioner (LRP+, LRP- lines) |
|
|
Left front seat belt internal failure (Left front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 21-3x: Short to Another Wire or Decreased Resistance in the Left Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the left front seat belt tensioner (LRP+, LRP- lines) |
|
|
Left front seat belt internal failure (Left front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 21-8x: Short to Power in the Left Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the left front seat belt tensioner (LRP+, LRP- lines) |
|
|
SRS unit internal failure | | |
|
DTC 21-9x: Short to Ground in the Left Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the left front seat belt tensioner (LRP+, LRP- lines) |
|
|
Left front seat belt internal failure (Left front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 22-1x: Open in the Right Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the right front seat belt tensioner (RRP+, RRP- lines) |
|
|
Right front seat belt internal failure (Right front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 22-2x: Increased Resistance in the Right Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right front seat belt tensioner (RRP+, RRP- lines) |
|
|
Right front seat belt internal failure (Right front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 22-3x: Short to Another Wire or Decreased Resistance in the Right Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the right front seat belt tensioner (RRP+, RRP- lines) |
|
|
Right front seat belt internal failure (Right front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 22-8x: Short to Power in the Right Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the right front seat belt tensioner (RRP+, RRP- lines) |
|
|
SRS unit internal failure | | |
|
DTC 22-9x: Short to Ground in the Right Front Seat Belt Tensioner
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the right front seat belt tensioner (RRP+, RRP- lines) |
|
|
Right front seat belt internal failure (Right front seat belt tensioner) |
|
|
SRS unit internal failure | | |
|
DTC 31-1x: Open in the Left Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the left side airbag inflator (LSA+, LSA- lines) |
|
|
Left side airbag internal failure (Left side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 31-2x: Increased Resistance in the Left Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left side airbag inflator (LSA+, LSA- lines) |
|
|
Left side airbag internal failure (Left side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 31-3x: Short to Another Wire or Decreased Resistance in the Left Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the left side airbag inflator (LSA+, LSA- lines) |
|
|
Left side airbag internal failure (Left side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 31-8x: Short to Power in the Left Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the left side airbag inflator (LSA+, LSA- lines) |
|
|
SRS unit internal failure | | |
|
DTC 31-9x: Short to Ground in the Left Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the left side airbag inflator (LSA+, LSA- lines) |
|
|
Left side airbag internal failure (Left side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 32-1x: Open in the Right Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the right side airbag inflator (RSA+, RSA- lines) |
|
|
Right side airbag internal failure (Right side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 32-2x: Increased Resistance in the Right Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right side airbag inflator (RSA+, RSA- lines) |
|
|
Right side airbag internal failure (Right side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 32-3x: Short to Another Wire or Decreased Resistance in the Right Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the right side airbag inflator (RSA+, RSA- lines) |
|
|
Right side airbag internal failure (Right side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 32-8x: Short to Power in the Right Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the right side airbag inflator (RSA+, RSA- lines) |
|
|
SRS unit internal failure | | |
|
DTC 32-9x: Short to Ground in the Right Side Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the right side airbag inflator (RSA+, RSA- lines) |
|
|
Right side airbag internal failure (Right side airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 33-1x: Open in the Left Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 33-2x: Increased Resistance in the Left Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 33-3x: Short to Another Wire or Decreased Resistance in the Left Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 33-8x: Short to Power in the Left Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
SRS unit internal failure | | |
|
DTC 33-9x: Short to Ground in the Left Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the left side curtain airbag inflator (LCA+, LCA- lines) |
|
|
Left side curtain airbag internal failure (Left side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 34-1x: Open in the Right Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 34-2x: Increased Resistance in the Right Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 34-3x: Short to Another Wire or Decreased Resistance in the Right Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to another line or Poor connection between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 34-8x: Short to Power in the Right Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to power between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
SRS unit internal failure | | |
|
DTC 34-9x: Short to Ground in the Right Side Curtain Airbag Inflator
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Short to ground between the SRS unit and the right side curtain airbag inflator (RCA+, RCA- lines) |
|
|
Right side curtain airbag internal failure (Right side curtain airbag inflator) |
|
|
SRS unit internal failure | | |
|
DTC 41-11: No Signal from the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left front impact sensor (LFS+, LFS- lines) |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 41-12: No Signal from the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left front impact sensor (LFS+, LFS- lines) |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 41-2x: Internal Failure of the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 41-9x, 41-Ax, 41-Bx: Internal Failure of the Left Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 42-11: No Signal from the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right front impact sensor (RFS+, RFS- lines) |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 42-12: No Signal from the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right front impact sensor (RFS+, RFS- lines) |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 42-2x: Internal Failure of the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 42-9x, 42-Ax, 42-Bx: Internal Failure of the Right Front Impact Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right front impact sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC 43-11: No Signal from the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (1st) (LS1+, LS1- lines) |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 43-12: No Signal from the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left side impact sensor (1st) (LS1+, LS1- lines) |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 43-2x: Internal Failure of the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 43-9x, 43-Ax, 43-Bx: Internal Failure of the Left Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 44-11: No Signal from the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (1st) (RS1+, RS1- lines) |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 44-12: No Signal from the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right side impact sensor (1st) (RS1+, RS1- lines) |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 44-2x: Internal Failure of the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 44-9x, 44-Ax, 44-Bx: Internal Failure of the Right Side Impact Sensor (1st)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right side impact sensor (1st) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 45-11: No Signal from the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the left side impact sensor (2nd) (LS2+, LS2- lines) |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 45-12: No Signal from the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the left side impact sensor (2nd) (LS2+, LS2- lines) |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 45-2x: Internal Failure of the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 45-9x, 45-Ax, 45-Bx: Internal Failure of the Left Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Left side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 46-11: No Signal from the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the right side impact sensor (2nd) (RS2+, RS2- lines) |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 46-12: No Signal from the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the right side impact sensor (2nd) (RS2+, RS2- lines) |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 46-2x: Internal Failure of the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect impact sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 46-9x, 46-Ax, 46-Bx: Internal Failure of the Right Side Impact Sensor (2nd)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Right side impact sensor (2nd) internal failure |
|
|
SRS unit internal failure | | |
|
DTC 51-xx: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC 52-xx: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC 53-FF: SRS Unit Programming Error
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit update not completed | | |
|
DTC 53-xx (except DTC 53-FF): Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC 54-xx: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC 55-xx: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC 56-21: Lost Communication with the PCM (PGM-FI system)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the PCM (F-CAN_H, F-CAN_L lines) |
|
|
SRS unit internal failure | | |
|
DTC 56-22: Undefined Data Received from the PCM (PGM-FI system)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the PCM (F-CAN_H, F-CAN_L lines) |
|
|
SRS unit internal failure | | |
|
DTC 56-23: Undefined Data Received from the PCM (PGM-FI system)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the PCM (F-CAN_H, F-CAN_L lines) |
|
|
SRS unit internal failure | | |
|
DTC 56-25: Lost Communication with the Gauge Control Module
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the gauge control module (F-CAN_H, F-CAN_L lines) |
|
|
Gauge control module internal failure |
|
|
SRS unit internal failure | | |
|
DTC 56-26: Undefined Data Received from the Gauge Control Module
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Gauge control module internal failure |
|
|
SRS unit internal failure | | |
|
DTC 56-27: Undefined Data Received from the Gauge Control Module
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Gauge control module internal failure |
|
|
SRS unit internal failure | | |
|
DTC 57-xx: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC 58-xx: Internal Failure of the SRS Unit
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit internal failure | | |
|
DTC A1-1x: Faulty Power Supply (VA line)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the under-dash fuse/relay box (VA line) |
|
|
Blown fuse (Under-dash fuse/relay box No. B29 (7.5 A)) |
|
|
SRS unit internal failure | | |
|
DTC A2-1x: Faulty Power Supply (VB line)
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open or Poor connection between the SRS unit and the under-dash fuse/relay box (VB line) |
|
|
Blown fuse (Under-dash fuse/relay box No. B3 (10 A)) |
|
|
SRS unit internal failure | | |
|
DTC A3-1x: SRS Unit Connector A Not Properly Installed
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and connector A |
|
|
SRS unit internal failure | | |
|
DTC A4-1x: SRS Unit Connector B Not Properly Installed
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and connector B |
|
|
SRS unit internal failure | | |
|
DTC B2-11: No Signal from the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the rear safing sensor (SSS+, SSS- lines) |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2-12: No Signal from the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Poor connection between the SRS unit and the rear safing sensor (SSS+, SSS- lines) |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2-2x: Internal Failure of the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Incorrect rear safing sensor installed |
|
|
Incorrect SRS unit installed |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2-9x: Internal Failure of the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the rear safing sensor (SSS+, SSS- lines) |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2-Ax: Internal Failure of the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the rear safing sensor (SSS+, SSS- lines) |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC B2-Bx: Internal Failure of the Rear Safing Sensor
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 6 seconds. | |
|
Duration |
About 6 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
Open, Short to another line, Short to ground, Short to power, or Poor connection between the SRS unit and the rear safing sensor (SSS+, SSS- lines) |
|
|
Rear safing sensor internal failure |
|
|
SRS unit internal failure | | |
|
DTC Ex-11: Control Operation Recorded
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 10 seconds. | |
|
Duration |
About 10 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit (Automatic shutdown recorded) | | |
|
DTC Fx-11: Airbags and/or Tensioners Deployment Recorded
|
Confirmation Procedure |
Basic Condition:
|
|
12 volt battery voltage 10 - 16 V |
Operating Condition:
|
1. |
Turn the vehicle to the ON mode, and wait 10 seconds. | |
|
Duration |
About 10 seconds |
|
DTC Type |
|
|
1 drive cycle |
|
|
SRS indicator on | |
|
Fail Safe Action |
|
|
Possible Cause |
|
|
SRS unit (Deployment recorded) | | |
| |
